![]() ![]() Sort load so that items of similar weight are washed together (refer to ' Sorting and loading'). Do not leave wet washing sitting in a washing basket. If not removing clothes from washer immediately at end of cycle, select the ‘Wrinkle Free’ option (WH8560F, WH8060F, WH8560P, WH8060P and WH7560P models only). Laundry left sitting wet is more likely to crease. Wet clothes left in washer or laundry basket. Use the ‘Easy Iron’ or ‘Handwash’ cycle for creasable items. Washing one item at a time is not recommended as it is difficult for the washer to balance a single item during spin. Wash an average sized load rather than a smaller load or a single item. The washer compensates for the out of balance by using a lower spin speed, to reduce noise and potential damage to itself.Įnsure transit bolts are removed prior to use of the machine (refer to ' Installation instructions').Įnsure washer is installed on an appropriate surface and levelled correctly (refer to ' Installation instructions'). Particularly short or delicate cycles have shorter spins which can result in wetter washing at the end of the cycle. Washing very wet at the end of the cycle. Liquid sitting at the ‘Max’ level at the end of the cycle indicates a blockage.Ĭlean the fabric softener dispenser (refer to ' Caring for your washer').Ĭlean out remaining detergent and refer to page ' Detergent and fabric softener' for dosing information. Recovery from out of balance or oversudsing will extend cycle time (refer to ' Before you call for service').īe aware that it will take longer for the machine to fill.īe aware that some options will extend cycle time.ĭetergent or fabric softener remaining in detergent dispenser at the end of the cycle.ĭetergent drawer not properly closed or was opened part way through the cycle.Įnsure the detergent dispenser drawer is fully closed at the start of the cycle and remains closed throughout the cycle.Ĭlean the detergent dispenser (refer to ' Caring for your washer'). Wash time may be influenced by a number of factors (refer to ' Washer controls').Įnsure that inlet hose filters are not blocked. If it sustains any damage it will need to be replaced.Ĭycle time longer than usual/Inaccurate time reading/ Adjustment of time remaining during cycle. Small puddle of water from under the machine.Ĭheck inlet hose(s) and the drain hose are correctly attached and not damagedĬlean detergent dispenser drawer (refer to ' Caring for your washer').ĭetergent dispenser drawer not fully closed.Ĭlose detergent dispenser drawer fully and ensure it remains closed during the cycle.Ĭheck seal inside door for damage. Use low sudsing, front loader detergent only (refer to ' Detergent and fabric softener'). Open door and redistribute load, then restart the washer.Įnsure machine is correctly levelled (refer to ' Installation instructions').Ĭheck the amount of detergent used, reduce if necessary. Use low sudsing, front loader detergent only (refer to ' Detergent and fabric softener').Įnsure the correct dose of detergent is used for the load size and soil level (refer to ' Detergent and fabric softener'). Lower the level of the drain hose (refer to ' Installation instructions').ĭrain hose not connected to standpipe or tub.Ĭonnect drain hose correctly (refer to ' Installation instructions').Įnsure standpipe or tub is at least 800mm from the floor level. Washer is waiting for suds to dissolve before continuing the cycle.Įnsure the height of the drain hose is at least 800mm from the floor level (refer to ' Installation instructions').Ĭlear the pump filter (refer to ' Caring for your washer').ĭrain hose higher than 1200 mm above floor level. Refer to ' Before you call for service' and ' Fault codes'.Ĭheck the power and/or water is working correctly. Check that the inlet hose is not twisted.Ĭheck taps that aren’t connected to the machine are working. Hot and cold taps not connected to the corresponding valve on the machine.Ĭheck the cold tap is connected to the cold valve on the machine and the hot tap is connected to the hot valve (if present).Ĭheck the tap end of the inlet hose(s) for blockages.Ĭheck the inlet hose for leaks or damage. If is flashing then the washer is waiting for a command from you.Ĭheck if a code is being displayed on the panel (refer to ' Before you call for service').Ĭheck that both hot and cold taps are turned on (if using cold inlet only ensure inlet valve cap is installed on the hot valve on the machine, if present). The washer is waiting for a command from you. Touch and hold the ‘Keylock’ button for 2 seconds (refer to ' Wash cycle options'). Try plugging in another electrical appliance.
0 Comments
Leave a Reply. |